GORLENKE10 Pack Metal Screed Pipe Chairs 2", Pin Caps,

GORLENKE10 Pack Metal Screed Pipe Chairs 2", Pin Caps, Pinheads, Concrete Tools, Fittings, Yokes, Easy Screed System
- Metal Screed Chairs are used to hold a 2” OD or smaller metal pipe to create a temporary rail at concrete grade for your screed to ride on. This will help to give you a flatter more accurate finished product. Our Screed Chairs are manufactured in the USA from metal that is manufactured in the USA. Metal Screed Chairs are virtually indestructible and can be used over and over again.
- Metal Screed Chairs are used when pouring up against a building or a wall or when the pad you are pouring is wider than your screed, you can set them in the center to hold a metal pipe at grade to screed off of. A Must for garage floors, basement floors, shop floors, and all concrete pad sizes. They can be used when pouring footings to give you a perfectly flat footing surface without having to use forms (see instructional videos).
- Metal Screed Chairs can also be used to help get your subgrade to perfect levels. Used for gravel leveling for concrete pads, or sand base leveling for patio or brick pavers, or even used for leveling dirt for landscaped areas (see instructional videos).
- To use Metal Screed Chairs you must first set a stringline to finished grade. If your pouring next to a wall you need to keep the stringline about 12" to 16" away from the wall to leave room for your screed to move. Next you need to cut 1/2" rebar to 18" - 24" in length. Drive those rebars about a half inch to one inch away from the stringline every 3'-4' apart.
- Using a hammer, drive the rebar into the ground until the top of the rebar is about the same level as the string line, then using the grade tool, finish driving them with a hammer till the pointer on the tool lines up with the string line (the grade tool is designed for a 2” OD metal pipe).
- If you are not using the grade tool you can use a tape measurer to set the top of the rebar to 2-1/4” below the stringline if using a 2” OD metal pipe. Next place the Metal Screed Chair on top of these rebars to provide a saddle for the temporary screed pipe. A 2" OD pipe 10’-20’ long is used and is slid forward to the next set of Metal Screed Chairs after you have screed through that section of the concrete, leaving the Screed Chairs free to remove, wash off and reuse
- Use these against a building or in the center of a larger pour to provide an accurate and moveable screed system.
- We have grade plates you can install if you’re driving the rebars in softer ground to help keep the rebars from sinking while screeding (recommended when using heavy screed pipes or larger screeding equipment). The grade tool, grade plates and other accessories are available to purchase separately. The grade tool makes setting the chairs to grade very easy and quick.
Package of 10 New Metal Screed Pipe Chairs The screed chairs are used when pouring next to a building or wall or when your pad is wider than your screed you can set them in the center to screed off of. A Must for garage and basement floors. First set a stringline 12 to 16 inches away from the wall your pouring against. Next cut 1/2" rebar to 18 - 24 inches in length. Drive those rebars about an inch and a half away from the string every 3-4 feet apart. Using a hammer drive them into the ground till the top of the rebar is about the same level as the string line, then using the rebar driving tool finish driving them with a hammer till the pointer on the tool lines up with the string line. Screed Chairs sit on these rebars and provide a saddle for the temporary screed pipe. A 2" OD pipe is used and is slide forward as you screed the concrete, leaving the Screed Chairs to remove and reuse. Use these against a building or in the center of a larger pour to provide an accurate and moveable screed system. We have grade plates you can install if your driving the rebars in softer ground to help keep the rebars from sinking while screeding. Look at my other auctions for these. The driver tool is available for purchase it makes driving the chairs to grade very easy and quick. We have also a great formless footing system using the screed chairs along with rebar supports that make pouring footings very quick and easy using no forms, a great time saver. Email for a discount quote on larger quantities. Watch instructional video http://youtu.be/TCtTIztFSuo
Country USA
Brand Redline Sales
Manufacturer Redline Sales
Model rxzer23
Color Grey
UnitCount 1
UPCs 639767920940
EANs 0639767920940
ReleaseDate 0000-00-00

Country	USA
Brand	Redline Sales
Manufacturer	Redline Sales
Model	rxzer23
Color	Grey
UnitCount	1
UPCs	639767920940
EANs	0639767920940
ReleaseDate	0000-00-00

GORLENKE10 Pack Metal Screed Pipe Chairs 2", Pin Caps, Pinheads, Concrete Tools, Fittings, Yokes, Easy Screed System

You might also like...