Degraw DIY Speaker Kit - PAM8403 5V Amplifier + 2x 4 ohm, 3W Speakers - Mini Class D Digital Audio Amplifier Module for Arduino - Includes 3.5mm Plug
Product Description
Degraw DIY Speaker Kit - PAM8403 5V Amplifier + 2x 4 ohm, 3W Speakers - Mini Class D Digital Audio Amplifier Module for Arduino - Includes 3.5mm Plug
- Updated version, quality is improved! Everything you need except a power supply for adding sound to a project.
- PAM8403 - Powerful and small Class D amplifier mounted on a 28 x 20 mm breakout board. Includes a super smooth potentiometer combination volume / on-off knob. Also includes header pins.
- Mini speakers - 2 pcs. 4 ohm, 3w, 31 mm x 70 mm. The same speakers found in flatscreen TV's and monitors.
- 3.5 mm cord - Includes 50 cm (19 in) headphone style cord and plug for easy phone or Raspberry Pi connection
- Easily power the kit with any 5V supply (not included): USB cell phone charger, 3 AA batteries, or a cell phone battery bank. Soldering required (header pins included). Do not apply power to the amplifier without speakers connected, this will result in damage to the amplifier.
- 1 x PAM8403 amplifier on breakout board
- 2 x 4 ohm, 3 watt oval speakers
- 10 x Breakaway header pins for PAM8403 connection
- 1 x 50 cm (19 in) cord with 3.5 mm audio plug
Everything you need except a power supply to make speakers in one complete package!
Information
- Speakers - Sturdy steel construction with easy-to-solder lugs and 3.3 mm mounting holes. These speakers are often used in commercial flat screen monitors.
- PAM8403 - This top of the line class D amplifier mounted on a breakout board pairs perfectly with the speakers to provide great sound.
- Speaker specs:
-4 ohm, 3 watt power
-Wires already attached
-31 mm wide, 70 mm high, 18 mm deep.
-4 mounting holes, 3 mm diameter. - PAM8403 specs:
-Operation Voltage: 5V. Get power from USB supply, 3 AA batteries, or cell phone battery bank (power supply not included)
-Output power: 3w + 3w (3 watts to each speaker)
-Efficiency: up to 90%
-Knob: smooth turning knob to adjust volume and turn unit on / off
-Mounting: drill a hole and mount using the volume knob with the included nut and washer
-Includes breakaway headers for connection, soldering required
Connections:
- Refer to diagram picture for wiring
- Note: do not connect (-) or (+) speaker connections together, this will damage the amplifier
- Note: do not apply power without speakers connected, this will damage the amplifier
Technical Specifications
You might also like
MakerHawk 2pcs Arduino Speaker 3 Watt 8 Ohm Single Cavity Mini Speaker Full-Range Cavity Mobile Portable Advertising Machine Speaker Connector Separating One-to-Two Interface 3.3V 5V
Audio Amplifier Board, DROK 5W+5W Mini Amplifier Board PAM8406 DC 5V Digital Stereo Power Amp 2.0 Dual Channel Class D Amplify Module for Speaker Sound System DIY
HiLetgo 5pcs PAM8403 23W Mini Digital Power Amplifier Board AMP Class D 2.5-5V Input
Super Mini PAM8403 DC 5V 2 Channel USB Digital Audio Amplifier Board Module 2 3W Volume Control with Potentionmeter Switch Pack of 2
HiLetgo 5pcs Micro SD TF Card Adater Reader Module 6Pin SPI Interface Driver Module with chip Level Conversion for Arduino UNO R3 MEGA 2560 Due
Gikfun 2" 4Ohm 3W Full Range Audio Speaker Stereo Woofer Loudspeaker for Arduino (Pack of 2pcs) EK1725
HiLetgo 2pcs Arduino mp3 Player Mini MP3 Player Audio Voice Module TF Card U Disk Board DFPlayer Audio Voice Music Module
5PCS 200 Times Gain 5V-12V LM386 Audio Amplifier Module for Arduino EK1236
uxcell a15080600ux0275 Metal Shell Round Internal Magnet Speaker 2W 8 Ohm Pack of 4
DROK TDA7297 15W+15W Audio Power Amplifier Module AC/DC 9-18V 2.0 Dual Channel Stereo Amp Board, DIY Sound System Component