Embroidex Cap/Hat Hoop for Brother Babylock Singer Bernina

Embroidex Cap/Hat Hoop for Brother Babylock Singer Bernina Janome Singer Husqvarna Viking Pfaff Embroidery Machine
- ★ CAP/HAT EMBROIDERY MACHINE HOOP ATTACHMENT Will work with the Following machines:
- ★ Brother PC-8200/ PC-8500/ PC-8500D - Brother PC-6500 - Brother PE 700/ PE700II/ PE 750D/ PE-770/ PE-780D - Brother ULT-2001/ ULT-2002/ ULT-2003 - Brother Innovis 6000D/ Innovis 4500D/ Innovis 4000D/ Innovis 4000LTD/ Innovis 1000/ Innovis 1200/ Innovis 1250D/ Innovis 1500D/ Innovis 2500D/ Innovis 2800D Brother PE100/ PE150/ PE200/ PE170D/ PE180D/ PC700/ PC7500
- ★ Singer XL-150/ XL-5000/ XL-6000/ XL-1000 - Singer Futura CE-100/ CE-200 - Singer Futura CE-150/ CE-250/ CE-350 - Singer SES-1000/ SES-2000 Janome 9500/ 9700/ 300E/ 10000/ 10001/ 11000
- ★ Babylock Ellegante/ Ellegante 2 - Babylock Esante/ Babylock Esante 2 - Babylock Ellure / Ellure Plus - Babylock Ellageo/ Ellageo Plus - Babylock Ellisimo - Babylock ES1/ EM1/ EM2/ ESE/ ESE1/ ESE2 - Bernina BE170/ BE180/ BE500/ BE600
- ★ Elna 8006/ 9006 - New Home 9000/ 5000 - Pfaff 7500 - Simplicity SE2/ SE3 - Viking #1/ #1+/Designer 1 Note some of the above models only work with a larger hoop. Hoops must be larger than 5.25" x 4.5" for this cap hoop to work.
READY TO BE EMBROIDERED ON IN SEVEN SIMPLE STEPS Easy and convenient the baseball cap can be hooped and ready to be embroidered on in seven simple steps. - Step 1 - Pull shiny backing off of adhesive stabilizer. Adhere to the bottom of the Cap Hoopster. Make sure the stabilizer is taught and firmly attached to the Cap Hoop, allowing it to wrap around the edges of the Cap Hoopster if necessary. - Step 2 - Determine where design should go onto the cap. The use of a water-soluble pin will help center design. Just make sure a vertical and horizontal line intersecting at the center point of the design. - Step 3 - Loosen visor clamp by turning thumbscrew. Attach clear template with two holes to the two small pegs on the visor clamp. Loosen back strap on cap and slide the visor under the template and visor clamp. Center the area of the cap that will be embroidered. The markings on the cap and the template will help you to do this. - Step 4 - Make sure sweat band is pulled back before you tighten down on thumbscrew. a) You must prevent the sweatband from being stitched to the cap. Taping or pinning the sweat band may be necessary. b) Stand-up buckram (a non-fused backing) must be pulled back with sweatband. Cutting buckram liner an inch or two on each side, where it is stitched to the visor, will allow it to be pulled back neatly. - Step 5 - Press the cap down against the adhesive backing starting in the middle and working out. The cap must be as flat and smooth as possible. - Step 6 - Clamp the Cap Hoopster to the outer machine hoop on the side opposite where the machine hoop attaches to the embroidery unit. - Step 7 - Turn your machine on and set it up for embroidery as usual. Turn embroidery unit on and attach attach machine hoop. You may have to remove the foot and/or shank to do this. Use curser keys to center needle and begin to embroider designs onto the cap. Remember, design must be rotated clockwise a quarter turn.
Country USA
Brand Embroidex
Manufacturer Embroidex
Binding Kitchen
ItemPartNumber CAPH2
Model CAPH2
Color Green
UPCs 763985689546
EANs 0763985689546
ReleaseDate 0000-00-00

Country	USA
Brand	Embroidex
Manufacturer	Embroidex
Binding	Kitchen
ItemPartNumber	CAPH2
Model	CAPH2
Color	Green
UPCs	763985689546
EANs	0763985689546
ReleaseDate	0000-00-00

Embroidex Cap/Hat Hoop for Brother Babylock Singer Bernina Janome Singer Husqvarna Viking Pfaff Embroidery Machine

You might also like...