HOBBYMATE 5-in-1 QAV Quadcopter PDB-Board-BEC 5V/3A-12V, LED Light Controller, Flyaway Finder & Battey Low Voltage Alarm
Product Description
HOBBYMATE 5-in-1 QAV Quadcopter PDB-Board-BEC 5V/3A-12V, LED Light Controller, Flyaway Finder & Battey Low Voltage Alarm
- Specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
- Simplify wiring. The BEC 12V can be used to power the Camera, Video Transmitters,ect.
- Inbuilt 5V LED light controller, three flash modes can be choosed with the toggle switch of transmiter.
- Toggle the switch to trigger the buzzer beep crazy to help you find lost quad or flexed wing in tall grass or trees, this could be very helpful when crash.
- You could also connect it to three flash modes 5v led to achieve better effect. It also acts as a battery voltage monitor ; Once voltage gets below preset threshold , the buzzer & LED light will alert you.
Built-in 5 functions, small size & light weight,2oz copper & 4-layers PCB.
ESC & Battery solder tabs in pairs. BEC 5V / 12V Output LED indicators. TVS input protection
Input voltage: 9 - 26VDC, support 3S-6S lipo battery
1 Battery input & 4 ESC outputs. Regulated 5V and 12V outputs.LED power indicators (5V & 12V outputs)
4 pairs 5V LED light pads.Low voltage setting value indicators
Dimensions: 46x36x6mm ; Weight: 9g ; Mounting holes 30.5mm square spacing .
F1. PDB (ESC outputs)
F2. BEC 5V output
Designed for RC Receivers, Flight controllers, OSD, and Servos.DC/DC synchronous buck regulator,Voltage: 5.0 +/- 0.1VDC.
Continuous current: 3 Amps.Short-circuit tolerant (10 seconds/minute).5V is also on the Aux pins + & -.
If other 5V BEC in use, Pls remove the red wire on Aux pins.
F2. BEC 12V output
Linear regulator, very low noise.Standard output designed to power cameras and video transmitters,etc.
If the battery is 3S LiPo, Output voltage=3S LiPo voltage - 1V. Don't use BEC 12V to power VTX or Gimbals when 6S battery is in use.
F3. LED Light Controller
Total 4 pairs LED light pads, All the LED lights have the same status.LED light voltage should be 5V.
Pls use the Aux channel with toggle switch of three positions.
Middle position is OFF (Value=1400~1600).
Side position is LED ON (Value=1700~2000).
Three LED modes: Constant light, Slow flash(1Hz), Fast flash(3Hz)
F4. Lost Plane Finder
F5. Low Voltage Alarm Notify you once the cells reach preset voltage.
Technical Specifications
You might also like
HOBBYMATE 180Pcs Assorted M3 Nylon Screws Nut Standoffs Spacers for DIY Building of FPV RC Quadcopter Drone, PC mods
FPVDrone M3 Anti-Vibration Fixed Screws Mounting Hardware Standoffs Spacer for Flight Controller
LHI 7 Colors RGB 5050 LED Strip Night Light 12V with DIP Switch 30mm Wire for ZMR250 QAV250 FPV 250 RC FPV Quadcopter (4PCS)
LHI 2PCS WRA0053 XT60 Male W/14awg Silicon Wire 10cm
FrSky X4RSB 3/16CH Telemetry Receiver Full Range
Frsky XM Plus Mini Full Range Receiver Failsafe D16 Mode Support SBUS Up Compatible With Frsky X9D / X9D Plus X9E X12S Transmitter.
Matek Systems PDB XT60 Power Distribution Board BEC 5V 2A 12V 0.5A with XT60 Plug for DIY Quadcopter Output Support 6 ESC for X or H Design FPV Racing Quad
nidici 60pcs FPV Sponge Mat Landing Pad Anti-vibration Foam Sticky Tape for X QAV-X Quadcopter Multicopter Frame
Tattu 4S 1300mAh LiPo Battery 75C 14.8V Pack with XT60 Plug for RC Boat Heli Airplane UAV Drone FPV Skylark Emax Nighthawk 250
REALACC Mini Power Distribution Board With BEC 5V And 12V For 250 Quadcopter FPV Multicopter