Impresa 3 Pack Replacement for Vormax Toilet Tank Silicone

Impresa 3 Pack Replacement for Vormax Toilet Tank Silicone Flapper Seal Gasket 3’’ - American Standard 7381424-100.0070A
- Ideal Replacement: Compatible with American Standard 7381424-100.0070A Vormax silicone seal. Made from durable, dry-rot resistant silicone rubber. Equivalent to part 7381424-100.0070A.
- Stop Running Toilets: When the flapper doesn't tightly reseal against the flush valve, water will continue to flow down into the toilet bowl causing the water level in the tank to never reach the level necessary to shut off the water supply valve. Keep these flappers handy so you never have to worry about a running toilet, self flushes or ghost flushes.
- Value 3 Pack: If you have an American Standard VorMax model then you know that flappers do wear out over time. With this 3 pack value, you will be set for years to come!
- Works On Select American Standard Vormax Toilets: Compatible with American Standard VorMax Plus, Estate VorMax, Heritage VorMax and High Efficiency model toilets. If you have any questions about fit, please ask a question below.
- 5 Minute Install: Installation instructions for proper use below. Installation is simpler than you'd expect, and does not require any tools for installation. Please note: This is an aftermarket replacement product (produced by Impresa Products) meeting or exceeding the quality of OEM rings (based on in-house testing). We have no affiliation with or endorsement from American Standard or any of the brands mentioned in this listing.
Installation Instructions:
1. Turn off the water to your toilet. Before you can replace a faulty flush seal, you'll need to stop running water to the tank.
  Locate the shutoff valve on the lower part of the wall behind or beside the toilet.
  Turn the valve dial clockwise until it stops turning.
  Â
2. Empty the tank. Lift off the toilet tank lid and set it aside carefully. Then, flush the toilet.
  This will empty the tank of water, allowing you to work unobstructed.
  Â
3. Remove the bad flapper seal. The flapper is a circular sheet of rubber that sits over the hole that releases water from the tank to the toilet.
  It connects in 2 places-the tiny pegs on either side of the tubular overflow valve and a chain attached to the toilet handle lever.
  Unclip the chain first by removing the clevis pin from the clevis pin from the trip lever rod, then pull the edges of the flapper free from the pegs to remove it.
  Â
4. Connect the new flapper to the flush valve. Slide the holes on either side of the new seal over the pegs on the valve,Â
  then clip the lift chain to the lower end of the toilet handle lever.
  Lower the flapper to confirm that it sits securely over the flush valve with total coverage.
  Â
5. Adjust the chain length if needed. There should be enough tension in the chain connecting the flapper to the toilet handleÂ
  to open the valve easily when the toilet is flushed, but not so much that it pulls or weakens the seal.
  Give the handle a push to how it feels and adjust the chain as needed until you feel that perfect flush feel.
  Â
6. Test out the new flapper. Turn the water shutoff valve counterclockwise to refill the tank with water.
  Wait a few moments for the water level to rise well above the flush valve, then press the handle.
  The toilet shou
7. Country USA
  Brand IMPRESA
  Manufacturer Impresa
  Binding Unknown Binding
  ItemPartNumber FlapperSeal3pk
  Model FlapperSeal3pk
  UPCs 850008283529
  EANs 0850008283529
  ReleaseDate 0000-00-00

Country	USA
Brand	IMPRESA
Manufacturer	Impresa
Binding	Unknown Binding
ItemPartNumber	FlapperSeal3pk
Model	FlapperSeal3pk
UPCs	850008283529
EANs	0850008283529
ReleaseDate	0000-00-00

Impresa 3 Pack Replacement for Vormax Toilet Tank Silicone Flapper Seal Gasket 3’’ - American Standard 7381424-100.0070A

You might also like...