Keywish RF-Nano V3.0 Integrate nRF24L01 Wireless Module Mirco

Keywish RF-Nano V3.0 Integrate nRF24L01 Wireless Module Mirco USB Board ATmega328P Micro-Controller Board Compatible with Nano V3.0 (2 Pcs)
- Creative products, RF-Nano-Board: Keywish Upgraded nano board for arduino, The main chip is ATMEGA328P-MU QFN32,the latest bootloader (Arduino IDE 1.8.8) was burned down. It is fully compatible with the common nano board. RF-Nano-Board is PIN-PIN with Arduino Nano V3.0,and share the same codes.
- More convenient for application: Emakefun RF-Nano-Board integrates a NRF24L01+ module with arduino nano v3.0 board, which is very convenient for 2.4G wireless connect application.
- High quality material and Technology: We used high quality PCB original material and Immersion Gold Technology to make sure every board has smooth edge and more reliable.
- Super small volume design, more convenient to use: The PCB size is only 48mm*19mm, the pin is fully compatible with Nano V3.0,No Soldering needed. The micro usb port is more convenient to use.
RF-Nano: Note: Please use Arduino IDE 1.8.6 or higher version, First, install the CH340 driver,then follow this selection path in Arduino IDE：Tools - Board"Arduino Nano" Processor "ATmega328P" Intruction: The Nano Board has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega328P provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1). A SoftwareSerial library allows for serial communication on any of the Nano's digital pins. The ATmega328P also support I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the I2C bus. To use the SPI communication, please see ATmega328P datasheet. Specification: Microcontroller ATmega328P Nrf24L01+ 2.4G wireless Architecture AVR Operating Voltage 5 V Flash Memory 32 KB of which 2 KB used by bootloader SRAM 2 KB Clock Speed 16 MHz Analog I/O Pins 8 EEPROM 1 KB DC Current per I/O Pins 40 mA (I/O Pins) Input Voltage 7-12 V Digital I/O Pins 22 PWM Output 6 Power Consumption 19 mA PCB Size 48 x 18mm Weight 7 g Package including: Keywish Nano x1
Country USA
Brand Keywish
Manufacturer Keywish
Binding Personal Computers
ItemPartNumber fba-RF-NANO-2pcs
Color RF Nano soldring
UPCs 799968211572
EANs 0799968211572
ReleaseDate 0000-00-00

Country	USA
Brand	Keywish
Manufacturer	Keywish
Binding	Personal Computers
ItemPartNumber	fba-RF-NANO-2pcs
Color	RF Nano soldring
UPCs	799968211572
EANs	0799968211572
ReleaseDate	0000-00-00

Keywish RF-Nano V3.0 Integrate nRF24L01 Wireless Module Mirco USB Board ATmega328P Micro-Controller Board Compatible with Nano V3.0 (2 Pcs)

You might also like...