PX4 Pixhawk 4 FMUv5 Autopilot with NEO-M8N GNSS and PM07 Power Management Board
Product Description
PX4 Pixhawk 4 FMUv5 Autopilot with NEO-M8N GNSS and PM07 Power Management Board
- Faster Processor (216MHz) and Twice the RAM (512KB) - vs previous Pixhawk
- Internal IMU Cushioning Allows Direct-Mounting of the Autopilot (M2 threads)
- Includes Pixhawk4 GNSS(u-blox NEO-M8N)/Compass/LED/Safety Switch Module and Power Management (PM07) Board
- Data-ready signals from sensors are routed to individual interrupt and timer pins on the autopilot, enabling precise time-stamping for logged data
- First Pixhawk based on the FMUv5 Standard - Runs both ArduPilot and PX4 firmware
Pixhawk 4 Autopilot [Plastic Case], GNSS and PM07 Power Management Board The Pixhawk 4 is the latest update in the PX4 (Pixhawk) series of open hardware autopilots. It delivers incredible performance, flexibility, and reliability for controlling any autonomous vehicle. FMUv5 hardware is supported by both PX4 and ArduPilot Features and Specifications: FMU Processor: STM32F765 (ARM Cortex-M7, 216MHz, 2MB SRAM, 512KB RAM) IO Processor: STM32F100 (ARM Cortex-M3, 24MHz, 8KB SRAM) IMU1: TDK InvenSense ICM-20689 IMU2: Bosch Sensortec BMI055 Magnetometer: iSentek IST8310 Barometer: MEAS MS5611 GNSS Unit: u-blox NEO-M8N GPS/GLONASS/Galileo GNSS and IST8310 mag Interfaces: 8-16 PWM servo outputs (8 from IO, 8 from FMU) 3 PWM/Capture inputs on FMU RC input for (C)PPM, Spektrum/DSM, and S.Bus with RSSI S.Bus servo output 6 serial ports: 2 w/HW flow control, 1 rated 1.5A 3 I2C ports 4 SPI Buses: 1 int high-speed SPI sensor bus w/4 CS and 6 DRDYs 1 int LN SPI bus for Barometer w/2 CS; no DRDYs 1 int SPI bus supports SPI calibration EEPROM on sensor 1 ext SPI bus 2 CANBuses for dual CAN w/serial ESC 2 sets of inputs for voltage/current monitoring 2 additional analog inputs Pixhawk4 Max input voltage: 6V Power module input: up to 50VDC Max (12S) Power module output: 4.9~5.5V Max current sensing: 120A Max Servo Rail Power Input: 36V Controller Size: 44x84x12mm, What's in the box? Pixhawk4, GNSS Unit, and PM07 Board 8GB SanDisk MicroSD card I2C splitter GNSS stand w/70 and 140mm rods 6x3 and 8x3 pin headers Full cable set (as pictured) Quick Start Guides Compatibility: PX4 and ArduPilot PX4 and Pixhawk are trademarks registered to L. Meier 9/2019 DevTu, LLC
Technical Specifications
You might also like
FrSky Taranis Compatible Receiver X8R 8-Channel 2.4ghz ACCST&RSSI&SBUS Easy to Use Receiver
Holybro 500mW Telemetry Radio Set (V3 for Pixhawk4) (915MHz)
NVIDIA Jetson Nano Developer Kit
GH1.25 Cables and connectors Wire for Pixhawk2 Pixhawk 4 Pixracer PXFmini Edge CUAV V5
RAYCorp® 1045 10x4.5 Propellers. 8 Pieces(4 CW, 4 CCW) Black & Red High Quality 10-inch Quadcopter and Multirotors Props + Battery strap
Readytosky 3DR Radio 915Mhz 500MW Telemetry Kit Air and Ground Data Transmit Module for Standard Version APM2.6 APM2.8 Pixhawk PX4 2.4.6 2.4.8 Flight Controller
ShareGoo Glass Fiber Shock Absorber Board Anti-vibration Damping Plate Mount for APM2.6 APM2.8 Pixhawk PX4 Flight Controller
powerday APM Power Module V1.0 XT60 Female Male Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller
LHI 4x 2212 920KV Brushless Motor (CW / CCW) + 4x SIMONK 30A ESC For DJI Phantom
Finware 10 Pair XT60 XT-60 Male Female Bullet Connectors Power Plugs with Heat Shrink for RC Lipo Battery