RAINPAL RBS024 Brass Rain Barrel Spigot (LF Compliant 3/4"

RAINPAL RBS024 Brass Rain Barrel Spigot (LF Compliant 3/4" Quarter Turn Ball Valve w/Bulkhead Fitting and Thread Tape, 7 GPM)
- Large 13mm Flow Port (7GPM), Large 3.5 inch Stainless Steel Handle. Freeze Proof
- ATTENTION: REVERSE THREADED FITTING NUT, Turn CLOCKWISE to LOOSEN.
- 3/4" Solid Brass Quarter Turn Valve w/ Brass Female 3/4" Bulkhead Fitting
- FEATURES: Lead Free Compliant Brass, Quarter Turn Ball Valve, Large 3.5" Stainless Steel Handle, Stainless Steel Nut, Freeze Resistant, Large Flow Port(7 GPM tested with 2 ft water), Recessed Rubber Gasket won't Pop Out
- SPECS: Bulkhead fitting need 32mm or 1-1/4 inch diameter hole to install. Fit up to 0.4 inch Thickness Wall(Works great for 55 gallon used plastic drum barrels on craigslist). Large 13 mm Port, Heavy and Heavy Duty, Net Weight: 11.5 oz
- Compare Design, Compare Material, Compare Weight, Compare Build Quality, and Choose RAINPAL, Life Time Warranty Against Leak, Break or Crack.
- Free Replacement Gasket upon Request
California prop 65 warning: California prop 65 warning: This product contains lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.

Contain less than 0.25% lead, lead free compliant. OK for potable water. For more information about lead free complianct, please visit epa.gov

Wear eye protection when operating power tools.

Installation Instructions(copyright OLDEGG INNOVATIONS LLC, OLDEGGINNOVATIONS.COM):

Tools Needed: 1-1/4 inch saw, Power drill, Knife, Pipe Wrench and Thread Tape

1. Center the hole saw drill bit 3-12 inch above the bottom of the barrel (lower position makes you use most of the water, higher position keeps more water and make barrel more stable, higher position also make it easy to dispense the water without using a stand). Drill 1-1/4 inch hole on rain barrel(use eye protection when operating power tool). Then remove any debris, and use a knife to smooth the edges.
2. If your barrel has an open top, you can install the fitting with nut inside or outside. If your barrel has a small opening like a bung hole on top: Drop the bulkhead fitting male piece with the gasket. Roll the barrel; pick up the fitting through the hole you drilled from outside. Or to prevent the gasket from separating from the fitting, you can hook the fitting with a wire, and then run the wire down to the drilled hole.
3. Install the bulkhead fitting nut, turn counter clockwise to tighten, after hand tight, use a pipe wrench to tighten a bit more.
4. Wrap the BASE of spigot threads with Teflon tape (5 rounds) and install the spigot clockwise. If the spigot is not in a desired position, loosen the fitting nut, turn the spigot to the right position then tighten the fitting nut. TIP: for easy un-installation later, only lightly tighten the spigot/ball valve. When uninstall, remove the ball valve first.
Country USA
Brand RAINPAL
Manufacturer RAINPAL
Binding Tools & Home Improvement
ItemPartNumber RBS024
Model RBS024
Color Brass
UPCs 681441045272
EANs 0681441045272
ReleaseDate 0000-00-00

Country	USA
Brand	RAINPAL
Manufacturer	RAINPAL
Binding	Tools & Home Improvement
ItemPartNumber	RBS024
Model	RBS024
Color	Brass
UPCs	681441045272
EANs	0681441045272
ReleaseDate	0000-00-00

RAINPAL RBS024 Brass Rain Barrel Spigot (LF Compliant 3/4" Quarter Turn Ball Valve w/Bulkhead Fitting and Thread Tape, 7 GPM)

You might also like...