30 Amp RV Power Inlet Replacement Direct Fit L5-30P Twist Lock

30 Amp RV Power Inlet Replacement Direct Fit L5-30P Twist Lock with Stainless Steel Pins Shore Power Inlet for Travel Trailer Camper 125V 30A
- -30 Amp Shore Power Inlet ：Enables easy, secure connection from campground power to your RV or travel trailer. Simply plug in your 30 amp extension cord to any standard 125V outlet, supplying reliable power for all your appliances and onboard systems.
- -Rated for 30A 125V ：Handles up to 3,750W setups. Features a 3-prong male, ETL-approved plug.Twist-lock design ensures a secure,weatherproof connection, while the attached flip-up cover protects the inlet from dust and water when not in use.
- -Built to Last ： Made from rugged, UV-stabilized glass-filled polyester,the power inlet is engineered to resist corrosion and withstand harsh outdoor conditions for reliable, long-term performance.
- -Easy Installation : The hardest step is cutting a clean 2.75" hole. Connect using 8 or 10 AWG wire: Black (125V Load), White (Neutral to ground bar), and Green (Equipment Ground, no load). Using undersized wire can overheat and create a fire hazard. Note: Installation screws are not included.
- -Application : Designed as a direct replacement for worn inlets or a new shore power connection in any RV, camper, van, or boat. Complete with step-by-step instructions for easy installation, it's also ideal for safely connecting a backup generator.
WARING:
The inlet is not to be connected to power prior to installation.Failure to comply with this instruction could result in an electrical failure,fire and electrocution.
New Installation
1. Determine mounting location in hull.Be careful that the location you select for the mounting hole does not go through any electrical wiring,plumbing or other obstruction.All power tools must be properly grounded.
2. Mark the installation location and cut opening in hull using hole saw(30amp 2-7/8"diameter hole.)
3. Place the inlet in the opening and align so that the inlet is square with the hull.Use the inlet as a template and mark the mounting hole location with a pencil.Remove inlet and drill mounting holes using 1/8"drill bit.
4. Remove the rear safety enclosure from the inlet.
5. Pull internal wiring through hull opening.Note:the 30amp inlet requires the use of 8AWG or 10AWG wire.Do not use the small gauge wire as this will result in overheating and possible electrical fire.
6. Thread the wiring through the rear safety enclosure and the strain relief on rear enclosure(if included),then slide the mounting gasket over the wiring.
7. Back off terminal screws on the rear housing of the inlet.
8. Strip wire end to 3/4.Make sure the wire strands are clean and not corroded.If necessary,cut back the wire until clean wire in uncovered.Do not solder the ends of the wire.Insert wires into color coded openings on the back of the inlet.Tighten terminal screws to 20 in.-lbs.torque.Make certain there is no wire insulation nder any terminal.
9. Tighten the strain relief clamp screws until they are tight around the wiring.Slide the rear safety enclosure onto the back of the inlet.
10. Position the gasket and inlet over the hull opening,align the mounting holes and attach the inlet to the hull with screws.
11. Use #8 pan head stainless steel screws to install the inlet.
Country USA
Brand Malxs
Manufacturer Malxs
Binding Misc.
ItemPartNumber POWER INLET -2
Model 1
Color WHITE
Size SQUARE
UnitCount 1
UPCs 754680760517
EANs 0754680760517
ReleaseDate 0000-00-00

Country	USA
Brand	Malxs
Manufacturer	Malxs
Binding	Misc.
ItemPartNumber	POWER INLET -2
Model	1
Color	WHITE
Size	SQUARE
UnitCount	1
UPCs	754680760517
EANs	0754680760517
ReleaseDate	0000-00-00

30 Amp RV Power Inlet Replacement Direct Fit L5-30P Twist Lock with Stainless Steel Pins Shore Power Inlet for Travel Trailer Camper 125V 30A

You might also like...