TIMESETL 5pcs DC 5V Stepper Motor 28BYJ-48 + 5pcs ULN2003

TIMESETL 5pcs DC 5V Stepper Motor 28BYJ-48 + 5pcs ULN2003 Driver Board + 40pcs Male Female Jumper Wire Cable for Arduino Raspberry PI
- [Standard Interface] This stepper motor comes with standard interface, direct plug and easy to use
- [4 Phase] A, B, C, D four-phase LED indicates the status of the stepper motor work
- [5 Lines] Use with ordinary ULN2003 chip driver(Included), connect to the 2 phase, support the development board, direct docking
- [Size] DC 5v step motor diameter 1.1 inch, cord length 9.5 inch, reduction ratio 1/64, step angle 5.625 x 1/64; driver board size 1.4 x 1.3 x 0.4 inch
- [40Pcs F-M Jumper Wire] Multicolor dupont wire female to male, 2.54mm 1 pin to 1pin, 8 inch(20cm) length
Geared Stepper Motor of TIMESETL

TIMESETL Arduino Motors - High Quality
Specification:
Stepper motor
Diameter: 1.1 inch (28mm)
Voltage: DC 5V
Length: 9.5 inch (23.9cm)
Step Angle: 5.625 * 1/64
Reduction ratio: 1/64
DC Resistance: 200Â¡Ã€7% (25)
Insulation Resistance: >10M (500V)
Dielectric Strength: 600V AC / 1mA / 1s
Insulation Grade: A
No-load Pull in Frequency: >600Hz
No-load Pull out Frequency: >1000Hz
Pull in Torque: >34.3mN.m(120Hz)
Detent Torque: >34.3mN.m
Temperature Rise: <40K(120Hz)
Noise: <40dB (120Hz, No load, 10cm)

Uln2003 driver test module: size 1.4 x 1.3 x 0.4 inch (3.5*3.2*1 cm)
Hole diameter: 3mm

Jumper wires male to female: 20cm/8inch length

TIMESETL Arduino Stepper Motor - Easy To Use

The stepper motor is a standard 4 phase design and is very easy to use.

Comes with an easy to use 5 pin connector attached to the end, keyed to ensure you do not connect it to the motor driver board backwards.

There is an LED for each output pin - this makes it easy to see which phases are currently active.

This stepper motor is bi-directional - you can run it clockwise or anti-clockwise.
To run the motor clockwise, you should activate the phases in this order:
Phase D
Phase D and Phase C
Phase C
Phase C and Phase B
Phase B
Phase B and Phase A
Phase A
Phase A and Phase D
And repeat...

To run the motor anti-clockwise, you should activate the phases in this order:
Phase A
Phase A and Phase B
Phase B
Phase B and Phase C
Phase C
Phase C and Phase D
Phase D
Phase D and Phase A
And repeat...

Delivery
5pcs x Driver Board
5pcs x Stepper Motor
40pin x Female Male Dupont Wire

Country	USA
Binding	Electronics
Brand	TIMESETL
Color	Stepper Motor
EAN	0611702529708
Label	TIMESETL
Manufacturer	TIMESETL
Model	TXJ-060-US
MPN	TXJ-060-US
PartNumber	TXJ-060-US
Publisher	TIMESETL
Size	φ28mm DC 5v step motor
Studio	TIMESETL
ReleaseDate	0000-00-00

TIMESETL 5pcs DC 5V Stepper Motor 28BYJ-48 + 5pcs ULN2003 Driver Board + 40pcs Male Female Jumper Wire Cable for Arduino Raspberry PI

You might also like...