Ulincos Touch Switch UT19T1 Stepless Dimming Switch DC 6V to 24V Blue LED Suitable for 19mm 3/4" Mounting Hole
Product Description
Ulincos Touch Switch UT19T1 Stepless Dimming Switch DC 6V to 24V Blue LED Suitable for 19mm 3/4" Mounting Hole
- Touch switch, just touch it!
- Stepless Dimming Type: You can Click or Holding Touch the switch to control your lights
- Blue LED ring always light ON, make you quickly find the switch at night or in the dark
- The wires replace the terminal pins, make installing very easy
- Dimming Switch, normally be used to control the lights. Don't exceed the rating amps and volts, you can run it on your other projects.
What You Get:
1 * Touch Switch
1 * Instruction
What's the Touch Switch:
Touch switch, just touch it!
The touch switch is rated for 7A MAX /DC 6-24V.
What's the Touch Switch Used for:
Most often the Stepless Dimming switch is used for lights (Such as critical lights, chassis lamp, dome light)
About Stepless Dimming type:
1.The light is off when connecting to electricity. Click it (time < 550ms) once to initiate it with the light on. Click it again to let it be off. Continue to cycle.
2.The initial brightness is 100% of the maximum brightness.
3.Touch and hold it (time > 550ms) to initiate stepless dimming control. The brightness increases when touching and holding, and stays at the level when stop holding. When holding more than 3 seconds, the brightness reaches and stays at maximum level. The brightness decreases when touching and holding again, and stays at the level when stop holding. When holding more than 3 seconds, the brightness reaches and stays at minimum level. Continue to cycle.
4.Click and Holding Touch can be used anytime. There is no interference between these two functions.
What's Note:
*The input power need to be constant-voltage source. A constant-current source (like LED driver, Output: DC12-24V 300ma) CANNOT fit the touch switch!
*The touch switch doesn't work with wet or damp fingers.
*The touch switch cannot be used in AC circuit. Don't exceed the rating volts!
Specifications:
Head diameter: 7/8" ( 22mm )
Mounting hole size: 3/4" ( 19mm )
Depth inc contacts: 1.1" ( 28mm )
Switch Type: Stepless Dimming
Input Voltage: DC 6V-24V
Output Current: 7A MAX
LED voltage: DC 6V-24V
LED color: Blue (always ON)
Enclosure material: Stainless Steel
Protection level: IK10
Operating Temperature: -20℃ ～ +55℃
Technical Specifications
You might also like
Ulincos Touch Switch UT19Z1 Latching Switch DC 6V to 24V, Blue LED Always On, Suitable for 19mm 3/4" Mounting Hole
On Off Switch, GLISTENY Strip Light Inline Light Dimmer Touch Control Dim Switch Touching Type Switch With Terminal For Led Light Strip Led Rigid bar Led Tape Light
Blue Sea Systems ST Blade Fuse Block - 12 Circuits with Negative Bus & Cover
65.6ft Extension Cable Wire Cord JACKYLED 20M 22AWG Wire Cord for Led Strips Single Color 3528 5050
Dicor BT-1834-1 1/8" x 3/4" x 30' Butyl Seal Tape
Blue Sea Systems Common 150A 10-Gang BusBar with Cover
acegoo 12V Reading Light, RV Boats LED Reading Lamp Dual Lighting Mode Directional Lighting with Dimmable Touch Switch Brushed Nickel, Hard-Wired
Wall-mounted Glass Touch Panel LED Dimmer Switch Brightness Controller DC 12-24V for Single Color LED Strip Light Lamp-White
Link Solar Weatherproof ABS Solar Double Cable Entry Gland for All Cable Types 2mm² to 6mm² for Solar Project on Rv, Campervan, Boat
Facon 12Volt DC Touch Dimmer Switch Use with LED lights, Incandescent and Halogen Bulbs for RV, Camper, Marine, and Strip Lights