MiOYOOW Soldering Practice Kit, Line Following Robot Car Kit

MiOYOOW Soldering Practice Kit, Line Following Robot Car Kit Beginners DIY Smart Car Soldering Project Kit for School Competition STEM Education, Learning Electronic Toys for 10+ Years Old Boys Girls
- ✔【School Science Project】: Smart DIY robot car is the most widely used in school for helping students to learn about the soldering project knowledge of mechanical structure, electronic basis skills, the principle of sensor, automatic control, soldering skill and so on.
- ✔【Its Principle】: As the light reflectivity is difererent when the light is emitting on the white and black items. It uses the photoresistance resistance to tell the smart car is on the right way or not. Smart tracking car can discriminate the direction automatically that it can run freely along the black tracking line.
- ✔【Design Your Runway】: You can also use the 1.5~2.0 cm black electrical tape directly on the ground to design the complex runway. It would be even more fun! This educational kit is perfect for holiday gifting and promotes valuable STEM skills!
- ✔【Easy Assembly】: This smart car solder practice kit is easy to build and the principle is simple. The connection that was clearly mapped and labeled on the PCB board. It's much easier to assemble which is great for students, teenagers, beginners and DIY hobbyists.
- ✔【English Manual】: We provide paper English instruction come with the product. You can scan the QR code in the last picture to get PDF manual. You can also download the Installation Manual on the Product Page Named "Technical Specification" Section (Due To Character Limit).
Download the material from drive.google.com/open?id=1kLlV2NlXQeXo56ItreQ1JlUParTRc-16 or just scan QR code on the 7th picture.

1>.Install circuit

1.1 Install metal film resistor,DIP-8P IC socket,Self-Locking switch,Potentiometer,S8550, Capacitor, Red LED on PCB according to mark on PCB

1.2 Install Mecanum wheel

The support bolts of the caster are inserted into the hole, tighten the nuts screwed into the caster, and finally fit the caster and tighten.

1.3 Install photoresistor and white LED on PCB reverse

1.4 Install battery case

1.5 Testing

Install 2pcs AA battery

Press on switch.If 2pcs white LED ON,the installation is successful.If LED off,please check the welding.

2>.Install mechanical parts

2.1 Install the four gaskets on the circuit board

2.2 Insert a steel shaft from the center hole of the wheel and note that the direction is inserted from one side of the raised sleeve of the wheel. It is better to insert the steel shaft parallel to the smooth side of the wheel

2.3 Put a three-way sleeve into the steel shaft, close to the wheel, and then a gasket into the steel shaft, close to the three-way sleeve, installed in place, toggle three-way sleeve, should be flexible.Â

2.4 Place a gear into the steel shaft in the center of the steel shaft

2.5 Put a three-axis sleeve into the end of the steel shaft so that the car side of the wheel assembly to complete

2.6 Install Motor

3>. Testing

Â 3.1 Power on.Check S8550 or 10ohm resistor if motor don't move

Â 3.2 Install LM393
Country USA
Brand MiOYOOW
Manufacturer WHDTS
Binding Misc.
ItemPartNumber 43234-1592
Model 10168
Color 1 Pack-soldering Tracking Car(dc Motor)
UnitCount 1
UPCs 615135207530
EANs 0615135207530
ReleaseDate 0000-00-00

Country	USA
Brand	MiOYOOW
Manufacturer	WHDTS
Binding	Misc.
ItemPartNumber	43234-1592
Model	10168
Color	1 Pack-soldering Tracking Car(dc Motor)
UnitCount	1
UPCs	615135207530
EANs	0615135207530
ReleaseDate	0000-00-00

MiOYOOW Soldering Practice Kit, Line Following Robot Car Kit Beginners DIY Smart Car Soldering Project Kit for School Competition STEM Education, Learning Electronic Toys for 10+ Years Old Boys Girls

You might also like...