Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (3/16") (#25 (3/16"))
Product Description
Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (3/16") (#25 (3/16"))
- Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.
- Diameter: 3/16", Length: 5.8 inches approximately. You get 1 piece of mosaic pin stock with each order. For knife handles.
- If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut (good for several knives). If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut (good for several knives). If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut (good for several knives).
- Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
- You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin due to inadequate vacuum pumping out of air bubbles prior to the curing stage).
Our mosaic pins are hand-crafted by a veteran knife-maker in the USA.
As a note: It is possible to drill a knife blank's pin holes larger (or create your own pin hole locations). You simply need to use drill bits intended for drilling metal, which are capable of drilling through hardened high carbon steel. This method is recommended because you be able will get the exact fit you are looking for when using our mosaic pins.
You will receive one piece of mosaic pin stock. Each piece comes in approximately 5.8" length.
We use only the highest quality brass, copper and steel.
If your knife handle is 0.75"-0.9" thick, this mosaic piece will make 6 pins when cut, good for several knives.
If your knife handle is 0.95"-1.15" thick, this mosaic piece will make 5 pins when cut, good for several knives.
If your knife handle is 1.2"-1.4" thick, this mosaic piece will make 4 pins when cut, good for several knives.
Our mosaic pins have been vacuum-pumped to remove air bubbles. The resin is pulled in with a high-end vacuum, which pulls the glue down, and removes any small bubbles. The pins are cured afterward and lastly polished and burrs removed.
The center of the mosaic pin is filled with clear epoxy resin. The filling will appear dark when initially received, however light will be able to shine through when you are done cutting this down to small pieces for your knife handle. The transparency will become evident with the smaller length pieces.
You wont get any "rattlers" with our high quality mosaic pins (a "rattler" is where you have loose pieces inside the mosaic pin).
A penny is shown for a size comparison. Penny not included.
Technical Specifications
You might also like
Whole Earth Supply Mosaic Pin Pins Knife Handle Custom Knives Blank Blades Brass Copper Steel for Hunting Knives (1/4") (#60 (1/4"))
5 pc Spacing Material for Knife Making
Texas Knifemakers Supply Bocote Wood Knife Handle Scales (Each Pair is Unique) 5" x 1-1/2" x 3/8"
Swpeet 18Pcs Assorted Brass Solid Round Rod Lathe Bar Stock Kit, Diameter 2mm-8mm Length 100mm, Perfect for Various Shaft, Miniature Axle, Model Plane, Model Ship, Model Cars
Bookmatched Zebrawood Knifes Scales, Handle Blank Exotic Knife Scales Wood
360 Brass Knife Pin Stock 3/16" x 6 inch 2pcs.
Whole Earth Supply 5 inch Black Buffalo Horn Gold Streaks Scales Handle Set Pair Handles Material for Knife Making Blanks Blades Knives Custom
MG Chemicals 415 Ferric Chloride Copper Etchant Solution, 945mL Liquid Bottle
RMP Knife Blade Steel - 1095 High Carbon Annealed Steel, Knife Making Billet, 1.5 Inch x 12 Inch x 0.187 Inch
G10 Spacer 5" X 10" X 1/32" Handle Material for knife making & gun making, (Complete Kit: Black, Blue, Orange, Red)